4.1
Updated
Service Literature
If you would like a copy of the Parts Catalog or Technical Manual for this machine call:
U.S. & Canada: 1-800-522-7448.
All Other Regions: Your John Deere dealer.
Parts
We recommend John Deere quality parts and lubricants, available at your John Deere dealer.
Part numbers may change, use part numbers listed below when you order. If a number changes, your dealer will have the latest number.
When you order parts, your John Deere dealer needs the serial number or product identification number (PIN) for your machine or attachment. These are the numbers that you recorded in the Product Identification section of this manual.
Order Service Parts Online
Visit http://JDParts.deere.com for your Internet connection to parts ordering and information.
Thank You for Purchasing a John Deere Product
We appreciate having you as a customer and wish you many years of safe and satisfied use of your machine.
Using Your Operator’s Manual
This manual is an important part of your machine and should remain with the machine when you sell it.
Reading your operator’s manual will help you and others avoid personal injury or damage to the machine. Information given in this manual will provide the operator with the safest and most effective use of the machine. Knowing how to operate this machine safely and correctly will allow you to train others who may operate this machine.
If you have an attachment, use the safety and operating information in the attachment operator’s manual along with the machine operator’s manual to operate the attachment safely and correctly.
This manual and safety signs on your machine may also be available in other languages (see your authorized dealer to order).
Sections in your operator’s manual are placed in a specific order to help you understand all the safety messages and learn the controls so you can operate this machine safely. You can also use this manual to answer any specific operating or servicing questions. A convenient index located at the end of this book will help you to find needed information quickly.
The machine shown in this manual may differ slightly from your machine, but will be similar enough to help you understand our instructions.
RIGHT-HAND and LEFT-HAND sides are determined by facing in the direction the machine will travel when going forward. When you see a broken line (------), the item referred to is hidden from view.
Before delivering this machine, your dealer performed a predelivery inspection to ensure best performance.
Special Messages
Your manual contains special messages to bring attention to potential safety concerns, machine damage as well as helpful operating and servicing information. Please read all the information carefully to avoid injury and machine damage.
Avoid injury! This symbol and text highlight potential hazards or death to the operator or bystanders that may occur if the hazards or procedures are ignored.
Avoid damage! This text is used to tell the operator of actions or conditions that might result in damage to the machine.
General information is given throughout the manual that may help the operator in the operation or service of the machine.
Parking Safely
Stop machine on a level surface, not on a slope.
Disengage mower blades or any other attachments.
Lower attachments to the ground.
Lock the park brake.
Stop the engine.
Remove the key.
Wait for engine and all moving parts to stop before you leave the operator’s seat.
Close fuel shut-off valve, if your machine is equipped.
Disconnect the negative battery cable or remove the spark plug wire(s) (for gasoline engines) before servicing the machine.
Protect Children
Death or serious injury can occur when young children associate having fun with a lawn mowing machine simply because someone has given them a ride on a machine.
Children are attracted to lawn mowing machines and mowing activities. They don’t understand the dangers of rotating blades or the fact that the operator is unaware of their presence.
Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine.
Tragic accidents with children can occur if the operator is not alert to the presence of children, especially when a child approaches a machine from behind. Before and while backing up, stop mower blades and look down and behind the machine carefully, especially for children.
Never carry children on a machine or attachment, even with the blades off. Do not tow children in a cart or trailer. They can fall off and be seriously injured or interfere with safe machine operation.
Never use the machine as a recreational vehicle or to entertain children.
Never allow children or an untrained person operate the machine. Instruct all operators not to give children a ride on the machine or in an attachment.
Keep children indoors, out of the mowing area, and in the watchful eye of a responsible adult, other than the operator, when a mower is being operated.
Stay alert to the presence of children. Never assume that children will remain where you last saw them. Turn the machine off if a child enters the work area.
Use extreme care when approaching blind corners, shrubs, trees, or other objects that may block your view of a child.
Keep Riders Off
Only allow the operator on the machine. Keep riders off.
Riders on the machine or attachment may be struck by foreign objects or thrown off the machine causing serious injury.
Riders obstruct the operator’s view resulting in the machine being operated in an unsafe manner.
Operating Safely
This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.
Read, understand and follow all instructions on the machine and in manuals provided, and view safety video, before starting. Be thoroughly familiar with the controls and the proper use of the machine before starting.
Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.
Only allow responsible adults, who are familiar with the instructions, to operate this machine. Local regulations may restrict the age of the operator.
Clear the area of objects such as rocks, wire and toys which could be thrown by the blades.
Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.
Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blades when crossing gravel surfaces.
Do not operate the machine without the entire grasscatcher, discharge guard, or other safety devices in place and working. Never operate with the discharge deflector raised, removed, or altered, unless using a grasscatcher.
Slow down before turning.
Never leave a running machine unattended. Always turn off blades, lock park brake, stop engine and remove key before dismounting.
Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grasscatcher, or unclogging the discharge chute.
Operate machine only in daylight or good artificial light.
Do not operate the machine while under the influence of alcohol or drugs.
Watch for traffic when operating near or crossing roadways. Stop blades before crossing roads or sidewalks.
Use extra care when loading or unloading the machine into a trailer or truck.
Always wear safety goggles or safety glasses with side shields when operating machine.
Data indicates operators 60 years and above are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury.
Follow the manufacturer’s recommendation for wheel weights or counterweights.
Inspect machine before you operate. Be sure hardware is tight. Repair or replace damaged, badly worn, or missing parts. Be sure guards and shields are in good condition and fastened in place. Make any necessary adjustments before you operate.
Before using, always visually inspect to see that the blades, blade bolts and the mower assembly are not worn and damaged. Replace worn and damaged blades and bolts in sets to preserve balance.
Make sure spark plug, muffler, fuel cap and air cleaner are in place before starting the engine.
Be sure all drives are in neutral and parking brake is locked before starting engine. Only start engine from the operator’s position.
Do not change the engine governor settings or overspeed the engine. Operating the engine at excessive speed can increase the hazard of personal injury.
If you hit an object or if abnormal vibration occurs, stop the machine and inspect it. Make repairs before you operate.
Use only accessories and attachments approved by the manufacturer of the machine. Keep safety labels visible when installing accessories and attachments.
Do not wear radio or music headphones. Safe service and operation requires your full attention.
When machine is left unattended, stored, or parked, lower the mower deck unless a positive mechanical lock is used.
Understanding The Machine Safety Labels
The machine safety labels shown in this section are placed in important areas on your machine to draw attention to potential safety hazards.
On your machine safety labels, the words DANGER, WARNING, and CAUTION are used with this safety-alert symbol. DANGER identifies the most serious hazards.
The operator’s manual also explains any potential safety hazards whenever necessary in special safety messages that are identified with the word, CAUTION, and the safety-alert symbol.
Replace missing or damaged safety labels. Use this operator’s manual for correct safety label placement.
There can be more safety information contained on parts and components sourced from suppliers that is not reproduced in this operator’s manual.
French or Spanish Safety Labels and Operator’s Manual
Operator’s manuals and safety labels with content in French or Spanish are available for this machine through authorized John Deere dealers. See your John Deere dealer.
Both text and no-text labels are shown. Your machine is only equipped with one of these types of labels.
Using a Spark Arrestor
The California Public Resources Code, section 4442.5 provides as follows:
No person shall sell, offer for sale, lease, or rent to any person any internal combustion engine subject to Section 4442 or 4443, and not subject to Section 13005 of the Health and Safety Code, unless the person provides a written notice to the purchaser or bailee, at the time of sale or at the time of entering into the lease or rental contract, stating that it is a violation of Section 4442 or 4443 to use or operate the engine on any forest-covered, brush-covered, or grass-covered land unless the engine is equipped with a spark arrestor, as defined in Section 4442, maintained in effective working order or the engine is constructed, equipped, and maintained for the prevention of fire pursuant to Section 4443. Cal. Pub. Res. Code 4442.5.
Other states or jurisdictions may have similar laws. A spark arrestor for your machine may be available from your authorized dealer. An installed spark arrestor must be maintained in good working order by the operator.
Checking Mowing Area
Clear mowing area of objects that might be thrown. Keep people and pets out of mowing area.
Low-hanging branches and similar obstacles can injure the operator or interfere with mowing operation. Before mowing, identify potential obstacles such as low-hanging branches, and trim or remove those obstacles.
Study mowing area. Set up a safe mowing pattern. Do not mow where traction or stability is doubtful.
Test drive area with mower lowered (if equipped) but not running. Slow down when you travel over rough ground.
Survey all mowing sites to determine which slopes are safe for machine operation and which slopes should be maintained through other maintenance techniques.
Rotating Blades are Dangerous
HELP PREVENT SERIOUS OR FATAL ACCIDENTS:
Rotating blades can cut off arms and legs, and throw objects. Failure to observe safety instructions could result in serious injury or death.
Keep hands, feet and clothing away from mower deck when engine is running.
Be alert at all times, drive forward and in reverse carefully. People, especially children can move quickly into the mowing area before you know it.
Before backing up, stop mower blades or attachments and look down and behind the machine carefully, especially for children.
Do not mow in reverse.
Shut off blades when you are not mowing.
Park machine safely before leaving the operator’s station for any reason including emptying the grasscatchers or unplugging the chute.
The mower blades should stop in approximately five seconds when the mower is disengaged. If you believe that your blades may not be stopping in that period of time, take your machine to your authorized dealer where they can safely check and service your machine.
Towing Loads Safely
Stopping distance increases with speed and weight of towed load. Travel slowly and allow extra time and distance to stop.
Total towed weight must not exceed combined weight of pulling machine, ballast and operator. Use counterweights or wheel weights as described in the attachment or pulling machine operator’s manual.
Excessive towed load can cause loss of traction and loss of control on slopes. Reduce towed weight when operating on slopes.
Never allow children or others in or on towed equipment.
Use only approved hitches. Tow only with a machine that has a hitch designed for towing. Do not attach towed equipment except at the approved hitch point.
Follow the manufacturer’s recommendations for weight limits for towed equipment and towing on slopes.
Towed attachments will increase the risk of rollover. Refer to the “Operating on Slopes” section for more information.
Do not turn sharply. Use additional caution when turning or operating under adverse surface conditions. Use care when reversing.
Do not shift to neutral and coast downhill.
Wear Appropriate Clothing
Always wear eye protection when operating the machine.
Wear close fitting clothing and safety equipment appropriate for the job.
While operating this machine, always wear substantial footwear and long trousers. Do not operate the equipment when barefoot or wearing open sandals.
Wear a suitable protective device such as earplugs. Loud noise can cause impairment or loss of hearing.
Driving Safely on Public Roads
Avoid personal injury or death resulting from a collision with another vehicle on public roads:
Use safety lights and devices. Slow moving machines when driven on public roads are hard to see, especially at night.
Whenever driving on public roads, use flashing warning lights and turn signals according to local regulations. Extra flashing warning lights may need to be installed.
Practice Safe Maintenance
Only qualified, trained adults should service this machine. Understand service procedure before doing work.
Never operate machine in a closed area where dangerous carbon monoxide fumes can collect.
Keep all nuts and bolts tight, especially blade attachment bolts, to be sure the equipment is in safe working condition.
Never tamper with safety devices. Check their proper operation regularly.
Keep machine free of grass, leaves or other debris build-up. Clean up oil or fuel spillage and remove any fuel-soaked debris. Allow the machine to cool before storing.
If you strike a foreign object, stop and inspect the machine. Repair, if necessary, before restarting.
Never make any adjustments or repairs with the engine running. Wait for all movement to stop on machine before adjusting, cleaning or repairing.
Check grasscatcher components and the discharge guard frequently and replace with manufacturer’s recommended parts, when necessary. Grasscatcher components are subject to wear, damage, and deterioration which could expose moving parts or allow objects to be thrown.
Mower blades are sharp. Wrap the blade or wear gloves, and use extra care when servicing them. Only replace blades. Never straighten or weld them.
Check brake operation frequently. Adjust and service as required.
Maintain or replace safety and instruction labels, as necessary.
On multi-bladed machines, take care as rotating one blade can cause other blades to rotate.
Keep hands, feet, clothing, jewelry, and long hair away from any moving parts, to prevent them from getting caught.
Lower any attachments to the ground before cleaning or servicing machine. Disengage all power and stop the engine. Lock park brake and remove the key. Let machine cool.
Securely support any machine elements that must be raised for service work. Use jack stands or lock service latches to support components when needed.
Disconnect battery or remove spark plug wire (for gasoline engines) before making any repairs. Disconnect negative terminal first and positive last. Install positive terminal first and negative last.
Before servicing machine or attachment, carefully release pressure from any components with stored energy, such as hydraulic components or springs.
Keep all parts in good condition and properly installed. Fix damage immediately. Replace worn or broken parts.
Charge batteries in an open, well-ventilated area, away from sparks. Unplug battery charger before connecting or disconnecting from the battery. Wear protective clothing and use insulated tools.
Do not strike the flywheel with a hammer or hard object because the flywheel may later shatter during operation.
If equipped with hydraulic lift - release hydraulic pressure by lowering attachment or cutting units to the ground or to a mechanical stop and move hydraulic control levers back and forth.
Avoid High Pressure Fluids
Hydraulic hoses and lines can fail due to physical damage, kinks, age, and exposure. Check hoses and lines regularly. Replace damaged hoses and lines.
Hydraulic fluid connections can loosen due to physical damage and vibration. Check connections regularly. Tighten loose connections.
Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure.
Search for leaks with a piece of cardboard. Protect hands and body from high pressure fluids.
If an accident occurs, see a doctor immediately. Any fluid injected into the skin must be surgically removed within a few hours or gangrene may result. Doctors unfamiliar with this type of injury should reference a knowledgeable medical source. Such information is available from Deere & Company Medical Department in Moline, Illinois, U.S.A. Information may be obtained in the United States and Canada only by calling 1-800-822-8262.
Handling Fuel Safely
To avoid personal injury or property damage, use extreme care in handling fuel. Fuel is extremely flammable and fuel vapors are explosive:
Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
Use only an approved fuel container. Use only non-metal, portable fuel containers approved by the Underwriter’s Laboratory (U.L.) or the American Society for Testing & Materials (ASTM). If using a funnel, make sure it is plastic and has no screen or filter.
Never remove the fuel tank cap or add fuel with the engine running. Allow engine to cool before refueling.
Never add fuel to or drain fuel from the machine indoors. Move machine outdoors and provide adequate ventilation.
Clean up spilled fuel immediately. If fuel is spilled on clothing, change clothing immediately. If fuel is spilled near machine, do not attempt to start the engine but move the machine away from the area of spillage. Avoid creating any source of ignition until fuel vapors have dissipated.
Never store the machine or fuel container where there is an open flame, spark, or pilot light such as on a water heater or other appliance.
Prevent fire and explosion caused by static electric discharge. Static electric discharge can ignite fuel vapors in an ungrounded fuel container.
Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before fueling.
Remove fuel-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a fuel dispenser nozzle.
Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until the fueling is complete. Do not use a nozzle lock-open device.
Never overfill fuel tank. Replace fuel tank cap and tighten securely.
Replace all fuel container caps securely after use.
For gasoline engines, do not use gas with methanol. Methanol is harmful to your health and to the environment.
Tire Safety
Explosive separation of a tire and rim parts can cause serious injury or death:
Do not attempt to mount a tire without the proper equipment and experience to perform the job.
Always maintain the correct tire pressure. Do not inflate the tires above the recommended pressure. Never weld or heat a wheel and tire assembly. The heat can cause an increase in air pressure resulting in a tire explosion. Welding can structurally weaken or deform the wheel.
When inflating tires, use a clip-on chuck and extension hose long enough to allow you to stand to one side and NOT in front of or over the tire assembly.
Check tires for low pressure, cuts, bubbles, damaged rims or missing lug bolts and nuts.
Checking Wheel Hardware
A serious accident could occur causing serious injury if wheel hardware is not tight.
Check wheel hardware tightness often during the first 100 hours of operation.
Wheel hardware must be tightened to specified torque using the proper procedure anytime it is loosened.
Handling Waste Product and Chemicals
Waste products, such as, used oil, fuel, coolant, brake fluid, and batteries, can harm the environment and people:
Do not use beverage containers for waste fluids - someone may drink from them.
See your local Recycling Center or authorized dealer to learn how to recycle or get rid of waste products.
A Material Safety Data Sheet (MSDS) provides specific details on chemical products: physical and health hazards, safety procedures, and emergency response techniques. The seller of the chemical products used with your machine is responsible for providing the MSDS for that product.
Prevent Fires
Besides routine maintenance, one of the best ways to keep your John Deere equipment running efficiently and to reduce fire risk is to regularly remove debris buildup from the machine.
Please review these recommendations with all operators. See your John Deere dealer with questions.
Always follow all safety procedures posted on the machine and in this operator manual. Before carrying out any inspection or cleaning, always shut off engine, set parking brake and remove ignition key.
After operating, allow machine to cool in an open area before cleaning or storing. Do not park machine near flammable materials such as wood, cloth or chemicals.
Empty any grasscatcher bags or containers completely before storing.
Frequency of these inspections and cleaning will vary depending on a number of factors including operating conditions, machine configuration, operating speeds and weather conditions particularly dry, hot and windy conditions. When you are operating in these conditions, inspect and clean these areas frequently throughout the day.
Wind direction, terrain type and moisture content of surrounding vegetation can effect where and how much debris accumulates.
Debris can accumulate anywhere on the machine, especially on horizontal surfaces.
Keeping engine area clean will provide the greatest impact on fire prevention. Other areas requiring regular inspection and cleaning include behind wheel rims, wire harness, hose/line routings, mowing attachments, etc. Compressed air, leaf blowers or high pressured water can assist keeping these areas clean.
Excess lubrication or fuel/oil leaks or spills on the machine can also serve as collection sites for debris. Prompt machine repair and oil/fuel cleanup will minimize the potential for debris collection and reduced cooling throughout machine life.
Bearing failures or overheating can result in a fire. To reduce this risk, always follow the instructions in the machine operator’s manual regarding lubrication intervals and locations. Washing the machine while warm may also reduce bearing life and increase potential for premature bearing failure.
Always shut off fuel when storing or transporting machine, if the machine has a fuel shutoff.
Charge and Connect Battery
The battery produces a flammable and explosive gas. The battery may explode:
Do not smoke or have open flame near battery.
Wear eye protection and gloves.
Never check battery charge by placing a metal object across the posts. Use a voltmeter or hydrometer.
Do not jump start or charge a frozen battery. Warm battery to specification.
Item
Measurement
Specification
Battery
Temperature
16°C (60°F)
Remove and discard the red positive (+) protective cap from the positive (+) battery terminal.
Charge the battery.
Battery is fully charged at 12.6 volts.
Connect positive (+) battery cable to battery.
Connect negative (–) battery cable.
Apply general purpose grease or silicone spray to terminal to help prevent corrosion.
Slide red cover over positive battery cable.
Check Tire Pressure
Check tire pressure. (See Checking Tire Pressure in the SERVICE MISCELLANEOUS section.)
Adjust Mower Deck Level
Adjust mower deck level. (See Adjusting Mower Deck Level in the OPERATING section.)
Check Engine Oil Level
Check engine oil level. (See Checking Engine Oil Level in the SERVICE ENGINE section.)
Check Machine Safety System
Perform safety system check to make sure the electronic safety interlock circuit is functioning properly. Perform all tests. (See Testing Safety System in the OPERATING section.)
Avoid Damage to Plastic and Painted Surfaces
Do not wipe plastic parts unless rinsed first. Using a dry cloth may cause scratches.
Insect repellent spray may damage plastic and painted surfaces. Do not spray insect repellent near machine.
Be careful not to spill fuel on machine. Fuel may damage surface. Wipe up spilled fuel immediately.
Prolonged exposure to sunlight will damage some surfaces.
Testing Safety Systems
Engine exhaust fumes contain carbon monoxide and can cause serious illness or death.
Do not run an engine in an enclosed area, such as a garage, even with doors or windows opened.
Move the machine to an outside area before running the engine.
The safety systems installed on your machine should be checked before each machine use. Be sure you have read the machine operator manual and are completely familiar with the operation of the machine before performing these safety system checks.
Use the following checkout procedures to check for normal operation of machine.
If there is a malfunction during one of these procedures, do not operate machine. See your authorized dealer for service.
Perform these tests in a clear open area. Keep bystanders away.
Testing Park Brake Switch
Park machine safely. (See Parking Safely in the SAFETY section.)
Sit on seat.
Unlock the park brake.
Try to start engine.
Result: Engine must not crank. If engine cranks, there is a problem with your safety interlock circuit.
Testing Park Brake
Park machine safely. (See Parking Safely in the SAFETY section.)
Lock the park brake.
Engage bypass valve control.
Try to push machine manually.
Result: Park brake must prevent machine from moving. If machine moves, parking brake needs to be adjusted.
Testing Mower Engagement (PTO) Switch
Park machine safely. (See Parking Safely in the SAFETY section.)
Sit on seat.
Lock the park brake.
Engage the mower.
Try to start engine.
Result: Engine must not crank. If engine cranks, there is a problem with your safety interlock circuit.
Unplugging Mower, Bagger, or Material Collection System
Do not attempt to unplug attachment with machine running.
Rotating blades are dangerous. Shut off the engine and remove the key before getting off the seat to inspect the machine and attachment.
Thrown objects can cause serious injury. Make sure all machine parts are stopped before raising hopper top or removing chutes.
Checking For Plugging While Driving
If grass builds up in front of mower discharge chute, check for plugged chute or problems with blower assembly (if equipped).
If there is a trail of clippings behind mower or clippings blow to the side, check for plugged chute, full collector bags, or problems with blower assembly.
Removing Debris From Inspection Points:
Do not use hands or feet to clear plugged mower deck or blower assembly. Stored energy can cause blades to rotate.
Park machine safely. Wait for all moving parts to stop before getting off to inspect machine.
Open hopper cover. Check chute outlet.
Remove chute from mower deck or blower assembly. Check chute inlet.
Check under mower deck for debris.
Servicing Your Machine
Operating in extreme conditions may require more frequent service intervals:
Engine components may become dirty or plugged when operating in extreme heat, dust or other severe conditions.
Engine oil can degrade if machine is operated constantly at slow or low engine speeds or for frequent short periods of time.
Please use the following timetables to perform routine maintenance on your machine.
Park the vehicle safely. See Park Safely in the SAFETY Section.
Grease
Use recommended John Deere greases to avoid component failure and premature wear.
The recommended John Deere greases are effective within an average air temperature range of -29 to 135 degrees C (-20 to 275 degrees F).
If operating outside that temperature range, contact your Servicing dealer for a special-use grease.
The following greases are preferred:
John Deere Multi-Purpose SD Polyurea Grease
John Deere Multi-Purpose HD Lithium Complex Grease
If not using any of the preferred greases, be sure to use a general all-purpose grease with an NLGI grade No.2 rating.
Wet or high speed conditions may require use of a special-use grease. Contact your Servicing dealer for information.
Avoid Fumes
Engine exhaust fumes contain carbon monoxide and can cause serious illness or death.
Do not run an engine in an enclosed area, such as a garage, even with doors or windows opened.
Move the machine to an outside area before running the engine.
Engine Oil
Use oil viscosity based on the expected air temperature range during the period between oil changes.
The following John Deere oils are preferred:
TURF-GARD™
PLUS- 4™
PLUS-50™ II
Other oils may be used if above John Deere oils are not available, provided they meet the following specification:
API Service Classification SJ or higher
Adjusting Carburetor
Carburetor is calibrated by the engine manufacturer and is not adjustable.
If engine is operated at altitudes above 1006 m (3,300 ft), some carburetors may require a special high altitude main jet. See your authorized dealer.
If engine is hard to start or runs rough, check the TROUBLESHOOTING section of this manual.
Possible engine surging will occur at high throttle with transmission in “N” neutral and mower engagement lever disengaged. This is a normal condition due to the emission control system.
After performing the checks in the troubleshooting section and your engine is still not performing correctly, contact your authorized dealer.
Checking for Bent Mower Blades
CAUTION: Blades are sharp. Always wear gloves when handling blades or working near blades.
Replace blades if defective. Never straighten or weld them.
Park machine safely. (See Parking Safely in the SAFETY section.)
Raise mower deck to highest position to access blades.
MXAL42867-UN: Mower deck with side discharge used for illustrationMeasure distance (A) between blade tip and flat ground surface. Rotate blade 180° and measure distance between other blade tip and flat ground surface.
Install new blade if the difference between the two measurements is more than 3 mm (1/8 in.).
Repeat for all blades.
Electrical
WARNING: Battery posts, terminals and related accessories contain lead and lead components, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.
Service the Battery Safely
The battery produces a flammable and explosive gas.
The battery may explode:
Do not smoke or have open flame near battery.
Wear eye protection and gloves.
Do not allow direct metal contact across battery posts.
Remove negative cable first when disconnecting.
Install negative cable last when connecting.
Cleaning Battery and Terminals
Park machine safely. (See Parking Safely in the SAFETY section.)
Disconnect and remove battery.
Wash battery with solution of four tablespoons of baking soda to one gallon of water. Be careful not to get the soda solution into the cells.
Rinse the battery with plain water and dry.
Clean terminals and battery cable ends with wire brush until bright.
Install battery.
Attach cables to battery terminals, beginning with the positive cable, using washers and nuts.
Apply spray lubricant to terminal to prevent corrosion.
Using Booster Battery
The battery produces a flammable and explosive gas.
The battery may explode:
Do not smoke or have open flame near battery.
Wear eye protection and gloves.
Do not jump start or charge a frozen battery. Warm battery to specification.
Item
Measurement
Specification
Battery
Temperature
16°C (60°F)
Do not connect the negative (-) booster cable to the negative (-) terminal of the discharged battery. Connect at a good ground location away from the discharged battery.
Connect positive (+) booster cable to booster battery (A) positive (+) post (C).
Connect the other end of positive (+) booster cable to the disabled vehicle battery (B) positive (+) post (D).
Connect negative (–) booster cable to booster battery negative (–) post (E).
IMPORTANT:
Electric charge from booster battery can damage machine components. Do not install negative booster cable to machine frame. Install only to the engine block.
Install negative booster cable away from moving parts in the engine compartment, such as belts and fan blades.
Connect the other end (F) of negative (–) booster cable to a metal part of the disabled machine engine block away from battery.
Start the engine of the disabled machine and run machine for several minutes.
Carefully disconnect the booster cables in the exact reverse order: negative cable first and then the positive cable.
Using Proper Fuel and Stabilizer
Using stale, contaminated or improper fuel can result in engine and fuel system damage. Repairs caused by stale, contaminated or improper fuel are not covered by warranty.
Use regular grade unleaded fuel with an octane rating of 87 octane or higher. Fuel blends containing up to 10% ethanol or up to 15% MTBE reformulated fuel are acceptable. Do not use fuel or additives containing methanol as engine damage can occur.
Always use fresh, clean fuel that is purchased in a quantity that can be used within approximately 30 days. Fuel stabilizer should always be added to the fuel each time fuel is purchased. Add stabilizer before filling the fuel container to insure proper mixing. Such practice helps prevent engine performance problems and allows fuel storage in the machine all year without draining.
Store fuel in plastic containers to reduce condensation. Make sure the cap on the fuel container is tight to reduce fuel contamination and evaporation. For best fuel storage life, use a self-sealing gas can.
Fuel is blended to give best seasonal performance. To avoid engine performance problems such as hard starting or vapor lock, use in-season fuel. Use fuel during warm weather that was purchased during that season, and use fuel during cold weather that was purchased during that season.
Fuel can become stale in machines with engines that are used seasonally or infrequently during a season. Stale fuel can produce varnish and plug carburetor or EFI components which can affect engine performance.
Keep fuel storage container tightly covered and in a cool area out of direct sunlight. Fuel can break down and degrade if not sealed properly or exposed to sun and heat.
Condensation may collect in the fuel tank because of a variety of operating or environmental conditions and, over time, may affect your machine’s operation. Fill machine fuel tank at the end of the day.
Filling Fuel Tank
Fuel vapors are explosive and flammable:
Shut engine off before filling fuel tank.
Allow engine to cool before refueling.
Do not smoke while handling fuel.
Keep fuel away from flames or sparks.
Fill fuel tank outdoors or in well ventilated area.
Clean up spilled fuel immediately.
Use clean approved non-metal container to prevent static electric discharge.
Dirt and water in fuel can cause engine damage:
Clean dirt and debris from the fuel tank opening.
Use clean, fresh, stabilized fuel.
Fill the fuel tank at the end of each day’s operation to keep condensation out of the fuel tank.
Use a non-metallic funnel with a plastic mesh strainer when filling the fuel tank or container.
Fill fuel tank at the end of each day’s operation to prevent condensation and freezing during cold weather.
Park machine safely. (See Parking Safely in the SAFETY section.)
Allow engine to cool.
Remove any trash from area around fuel tank cap.
Remove fuel tank cap slowly to allow any pressure built up in tank to escape.
Fill fuel tank only to bottom of filler neck. Do not overfill.
Install fuel tank cap.
Gas models: Turn cap until clicks.
Checking Tire Pressure
Explosive separation of tire and rim parts is possible when they are serviced incorrectly:
Do not attempt to mount a tire without the proper equipment and experience to perform the job.
Do not inflate the tires above the recommended pressure.
Do not weld or heat a wheel and tire assembly. Heat can cause an increase in air pressure resulting in an explosion. Welding can structurally weaken or deform the wheel.
Do not stand in front or over the tire assembly when inflating. Use a clip-on chuck and extension hose long enough to allow you to stand to one side.
Check tires for damage.
NOTE:
Refer to the SPECIFICATIONS section for tire pressures or check the side of the tire.
Check tire pressure with an accurate lower pressure gauge.
Add or remove air, if necessary.
Cleaning and Repairing Metal Surfaces
Cleaning:
Follow automotive practices to care for your vehicle painted metal surfaces. Use a high-quality automotive wax regularly to maintain the factory look of your vehicle’s painted surfaces.
Repairing Minor Scratches (surface scratch):
Clean area to be repaired thoroughly.
IMPORTANT:
Do not use rubbing compound on painted surfaces.
Use automotive polishing compound to remove surface scratches.
Apply wax to entire surface.
Repairing Deep Scratches (bare metal or primer showing):
Clean area to be repaired with rubbing alcohol or mineral spirits.
Use paint stick with factory-matched colors available from your authorized dealer to fill scratches. Follow directions included on paint stick for use and for drying.
Smooth out surface using an automotive polishing compound. Do not use power buffer.
Apply wax to surface.
Using Troubleshooting Chart
If you are experiencing a problem that is not listed in this chart, see your authorized dealer for service.
When you have checked all the possible causes listed and you are still experiencing the problem, see your authorized dealer.
Storing Safety
Fuel vapors are explosive and flammable.
Engine exhaust fumes contain carbon monoxide and can cause serious illness or death:
Run the engine only long enough to move the machine to or from storage.
Machine fires and structure fires can occur if a machine is stored before allowing it to cool, or if debris is not removed from around the engine and muffler, or if stored near combustible materials.
Do not store vehicle with fuel in the tank inside a building where fumes may reach an open flame or spark.
Allow the engine to cool before storing the machine in any enclosure.
Preparing Machine for Storage
Repair any worn or damaged parts. Replace parts if necessary. Tighten loose hardware.
Repair scratched or chipped metal surfaces to prevent rust.
Remove grass and debris from machine.
Clean under the deck and remove grass and debris from inside chute and bagger.
Wash the machine and apply wax to metal and plastic surfaces.
Run machine for five minutes to dry belts and pulleys.
Apply light coat of engine oil to pivot and wear points to prevent rust.
Lubricate grease points and check tire pressure.
Preparing Fuel and Engine For Storage
Fuel:
If you have been using “Stabilized Fuel,” add stabilized fuel to tank until the tank is full.
Filling the fuel tank reduces the amount of air in the fuel tank and helps reduce deterioration of fuel.
If you are not using “Stabilized Fuel:”
Park machine safely in a well-ventilated area. (See Parking Safely in the SAFETY section.)
NOTE:
Try to anticipate the last time the machine will be used for the season so very little fuel is left in the fuel tank.
Turn on engine and allow to run until it runs out of fuel.
For machines equipped with key switch, turn key to off position.
IMPORTANT:
Stale fuel can produce varnish and plug carburetor or injector components and affect engine performance.
Add fuel conditioner or stabilizer to fresh fuel before filling tank.
Mix fresh fuel and fuel stabilizer in separate container. Follow stabilizer instructions for mixing.
Fill fuel tank with stabilized fuel.
Run engine for a few minutes to allow fuel mixture to circulate through carburetor on gas engine or fuel injectors on diesel engine.
Engine:
Engine storage procedure should be used when vehicle is not to be used for longer than 60 days.
Change engine oil and filter while engine is warm.
Service air filter if necessary.
Clean debris from engine air intake screen.
On gas engines:
Remove spark plugs. Put 30 mL (1 oz) of clean engine oil in cylinder(s).
Install spark plugs, but do not connect spark plug wires.
Crank the engine five or six times to allow oil to be distributed.
Clean the engine and engine compartment.
Remove battery.
Clean the battery and battery posts. Check the electrolyte level, if your battery is not maintenance free.
Close fuel shut-off valve, if your machine is equipped.
Store the battery in a cool, dry place where it will not freeze.
NOTE:
The stored battery should be recharged every 90 days.
Charge the battery.
IMPORTANT:
Prolonged exposure to sunlight could damage the hood surface. Store machine inside or use a cover if stored outside.
Store the vehicle in a dry, protected place. If vehicle is stored outside, put a waterproof cover over it.
Removing Machine From Storage
Check tire pressure.
Check engine oil level.
Check battery electrolyte level, if your battery is not maintenance free. Charge battery if necessary.
Install battery.
On gas engines: Check spark plug gap. Install and tighten plugs to specified torque.
Lubricate all grease points.
Open fuel shut-off valve, if your machine is equipped.
Run the engine 5 minutes without the mower or any attachments running to allow oil to be distributed throughout engine.
Be sure all shields and guards or deflectors are in place.
Warranty
Product Warranty
Product warranty is provided as part of John Deere’s support program for customers who operate and maintain their equipment as described in this manual.
Engine related warranties stated in this manual refer only to emissions-related parts and components of your engine. The complete engine warranty, less emission-related parts and components, is provided separately as the “Limited Warranty for New John Deere Equipment”.
John Deere Quality
John Deere equipment is more than just a purchase, it’s an investment in quality. That quality goes beyond our equipment to your John Deere dealer’s parts and service support. This support is needed to keep you a satisfied customer.
That’s why John Deere has initiated a process to handle your questions or problems, should they arise. The following three steps will help guide you through the process.
Step 1
Refer to your operator’s manual
-: .
A. It has many illustrations and detailed information on the safe and proper operation of your equipment. | C. It gives ordering information for parts catalogs, service and technical manuals. |
B. It gives troubleshooting procedures, and specification information. | D. If your questions are not answered in the operator’s manual, then go to Step 2. |
Step 2
Contact your dealer
-: .
A. Your John Deere dealer has the responsibility, authority, and ability to answer questions, resolve problems, and fulfill your parts and service needs. | C. If the parts and service people are unable to resolve your problem, see the dealership manager or owner. |
B. First, discuss your questions or problems with your dealer’s trained parts and service staff. | D. If your questions or problems are not resolved by the dealer, then go to Step 3. |
Step 3
Contact John Deere
-: .
A. Your John Deere dealer is the most efficient source in addressing any concern, but if you are not able to resolve your problem after checking your operator’s manual and contacting your dealer, contact John Deere for assistance | |
B. For prompt, effective service, please have the following ready before you call: | |
The name of the dealer with whom you’ve been working. Your equipment model number. Number of hours on machine (if applicable). | Your serial number which you recorded on the inside front cover of this manual. If the problem is with an attachment, your attachment identification number. |
C. Then call 1-800-537-8233 (United States and Canada) and our advisor will work with your dealer to investigate your concern. If you are outside the United States and Canada, contact us at the following website: www.deere.com/wps/dcom/en_US/regional_home.page. | |
DANGER
ROTATING BLADES CUT OFF ARMS AND LEGS
Do not mow when children or others are around.
Do not mow in reverse.
Look down and behind before and while backing.
Never carry children even with blades off.
DANGER
ROTATING BLADE
Do not put hands or feet under or into mower when engine is running.
DANGER
Shield eyes, explosive gases can cause blindness or injury.
No sparks, flames, smoking.
Sulfuric acid can cause blindness or severe burns.
Flush eyes immediately with water. Get medical help fast.
Keep out of reach of children.
Do not tip.
Keep vent caps tight and level.
WARNING
To avoid injury from loaded spring
To avoid injury from loaded spring, read operator’s manual before changing attachments.
WARNING
AVOID SERIOUS INJURY OR DEATH
Drive up and down slopes, not across.
Avoid sudden turns.
If machine stops going uphill, stop blades and back down slowly.
Keep safety devices (guards, shields, and switches) in place and working.
Read operator’s manual.
Remove objects that could be thrown by blades.
When leaving machine:
Stop engine
Set park brake
Remove key
CAUTION
Avoid equipment fires.
Accumulation of grass, leaves and other debris on or near hot or moving parts can cause a fire.
Inspect machine before, during, and after use.
Shut off engine and allow machine to cool before cleaning.
Inspect and clean the entire machine and pay special attention to these locations:
Muffler and exhaust system
Engine and engine screens
Top of mower deck and under shields
On or near transmission
Testing Seat Switch
Test 1
Start the engine.
Move throttle lever to maximum speed position.
Unlock the park brake.
Engage the PTO switch.
Raise up off seat. Do not get off machine.
Result: Engine should begin to stop. PTO should shut off immediately and mower blades should stop.
Test 2
Disengage the PTO switch.
Start the engine.
Unlock the park brake.
Raise up off seat. Do not get off machine.
Result: Engine should stop. If engine does not stop, there is a problem with your safety interlock circuit.
Test 3
Start the engine.
Lock the park brake.
Raise up off seat. Do not get off machine.
Result: Engine should continue to run.
Using Park Brake
Children or bystanders may attempt to move or operate an unattended machine.
Always lock the park brake and remove the key before leaving the machine unattended.
Locking Park Brake
Push and hold down brake pedal.
Pull up park brake lever to lock park brake.
Release brake pedal. Pedal should stay down and park brake lever should stay up in locked position.
Unlocking Park Brake
Push and hold down brake pedal.
Push down park brake lever to unlock park brake.
Release brake pedal. Pedal should come up to operating position.
Stopping the Engine
Stop the machine.
Move throttle lever to half throttle position and allow engine to run at half throttle for several seconds.
Turn key to stop position.
Lock the park brake.
Remove the key.
Using Travel Controls
Children or bystanders may be injured by runover and rotating blades. Before traveling forward or rearward:
Carefully check the area around the machine.
Disengage the mower before backing up.
Forward Travel
Start the engine.
Unlock the park brake.
Push down slowly on forward pedal until desired travel speed is obtained.
Release forward pedal and machine will automatically return to neutral and stop.
Reverse Travel
Any operating attachment will stop as the reverse foot pedal is depressed with attachment engaged. Reverse attachment operation is possible using the Reverse Implement Option (RIO).
Stop the machine.
Push mower engagement knob down to the off position to disengage attachment.
Look down and behind the machine to be sure there are no bystanders nearby.
Push down slowly on reverse pedal.
Stopping
Release either travel pedal, machine will automatically return to neutral and stop.
Push down brake pedal.
Using Cruise Control
Do not use cruise control when going down hills. Machine speed will increase. Operate machine in a large, open area to learn how the cruise control works.
Use cruise control when you want to maintain travel speed without having to hold the forward travel pedal down. Cruise control operates only for forward travel.
Engaging Cruise Control
Push forward pedal down until you reach desired travel speed.
Lift up cruise lever.
Remove foot from forward pedal.
Release cruise lever.
Disengaging Cruise Control
Cruise control will also disengage if forward travel pedal is pressed.
Push brake pedal down.
Adjusting Tilt Steering Wheel (If Equipped)
Do not attempt to adjust the steering wheel while the machine is moving. The operator can lose control of the machine.
Stop the machine before adjusting the steering wheel.
Lock the steering wheel in position before driving the machine.
Steering wheel has five tilt positions:
Lift and hold lever (A) up and move wheel to a comfortable operating position.
Release lever and move wheel slightly up or down until lever drops into the nearest position and locks wheel.
Using the Reverse Implement Option (RIO)
Children or bystanders may be injured by runover and rotating blades. Before traveling forward or rearward:
Carefully check the area around the machine.
Disengage the mower before backing up.
Operating the mower while backing up is strongly discouraged. The Reverse Implement Option should be used only when operating another attachment or when the operator deems it necessary to reposition the machine with the mower engaged.
Stop forward travel. Allow attachment to run.
Look down and behind the machine to be sure there are no bystanders.
MXAL46368-UN: Mower SwitchLift mower engagement switch (A) past the mower engagement position then depress reverse foot pedal (B) slightly. NOTE:
If the attachment stops while positioning the machine, return mower engagement lever to off position. Repeat this procedure from the beginning.
As the machine begins to move backward, release the mower engagement lever and position the machine.
Resume forward travel. The attachment should continue operating.
Repeat procedure to position the machine again.
Using Mower Attachment / Mower Lift
If the machine is equipped with a lift assist spring, make sure the tension is properly adjusted to support the weight of the mower deck or attachment installed.
Mowing Position
Mower floats along ground contour while maintaining desired cutting height. The mower will always float up and back down onto the depth stop.
1. To place mower in mowing position:
Models with Mechanical Lift
Press lift pedal, making sure mower lift lock lever is in lower position; select cut height on knob and release pedal to lower deck.
Models with Hydraulic Lift
Pull up on hydraulic mower lift lever to raise mower deck. Select cut height on knob. Press down on hydraulic mower lift handle to lower deck.
Transport Position
Holds mower above ground level while traveling to and from worksite.
1. To place mower in the transport position:
Models with Mechanical Lift
Push forward on lift pedal.
Pull up on mower lift lock lever to lock deck in transport (raised) position.
Remove foot from lift pedal and mower stays up.
Models with Hydraulic Lift
Pull up on hydraulic mower lift lever to raise mower deck.
Using Mower Engagement Lever
Mower engagement operation will stop if reverse pedal is depressed. Understand the Reverse Implement Option (RIO) system before operating the mower.
Start the engine. If necessary, allow engine to warm up before operating mower.
NOTE:
Always operate at maximum throttle speed when mower is engaged.
Move throttle lever to fast position.
Move mower engagement lever to desired position:
Engage mower - Lift up on mower engagement lever to “l” position.
Disengage mower - Push down on mower engagement lever to “O” position.
Maintain mower engagement in reverse - Lift and hold mower engagement lever in the highest position. Depress reverse foot pedal to start moving in reverse, release mower engagement lever.
Using Wash Port to Clean Mower Deck
Follow this procedure after each use to prevent buildup and remove corrosive lawn chemicals.
Park machine safely. (See Parking Safely in the Safety section).
MXAL46369-UN: Wash PortAttach quick-coupler to garden hose. Attach garden hose with quick-coupler to wash port (A) on the mower deck.
Turn on water.
Start engine.
Run at full throttle.
Engage mower blades.
Flush water under deck for approximately one minute.
Disengage mower blades.
Stop engine.
Turn off water and remove garden hose and quick-coupler from wash port.
Remove quick-coupler from garden hose and store for future use.
Using Accessories
Using Heavy Duty CargO Mount™ System
The front and rear Heavy Duty CargO Mount™ brackets (A) can be used for easy attachment of selected optional equipment.
Use John Deere approved optional equipment only. See your Authorized Service Center for approved optional equipment.
48C and 54C Blade Choices
Two types of blades are available for X300 and X500 series 3-spindle mowers:
Side discharge blades. These blades are designed for optimal performance when side discharging and are installed on mowers when shipped from the factory.
Mulching blades. These blades are designed for optimal performance when used with a mulch kit installed.
Lubricating Front Axle
Lubricate grease fitting (A) on each spindle with one or two pumps of general all-purpose grease.
Turn wheels to distribute grease on spindles.
Lubricate front axle center pivot grease fitting (B) with one or two pumps of general all-purpose grease.
Lubricating Rear U-Joints (4-Wheel Steer Models)
Lubricate steering pivot grease fitting (A) at each wheel with recommended grease.
Turn steering wheel back and forth to distribute grease.
Lubricating Lift Pedal Assembly
Lubricate grease fitting (A) for lift pedal with enough grease to flush out dirt.
Remove excess grease.
Checking Engine Oil Level
Failure to check the oil level regularly could lead to serious engine problems if oil level is out of the operating range:
Check oil level before operating.
Check oil level when the engine is cold and not running.
Keep oil level between the dipstick marks.
Shut off engine before adding oil.
Check oil twice a day if you run engine over 4 hours in a day.
Make sure engine is cold when checking engine oil level.
Park machine safely. (See Parking Safely in the SAFETY section.)
Lift hood.
Clean area around dipstick to prevent debris from falling into crankcase.
MXAL46383-UN: DipstickRemove dipstick (A). Wipe with clean cloth. Install dipstick in tube but do not tighten. Allow dipstick threads to rest on top of tube and rotate cap counterclockwise until it “clicks” or drops into place.
Remove dipstick.
Check oil level on dipstick. Oil must be between ADD and FULL marks.
If oil level is low, add oil to bring oil level no higher than FULL mark on dipstick. Do not overfill.
Install and tighten dipstick. Lower hood.
Cleaning Engine Shroud
Compressed air can cause debris to fly a long distance.
Clear work area of bystanders.
Wear eye protection when using compressed air for cleaning purposes.
Reduce compressed air pressure to 210 kPa (30 psi).
An obstructed air intake screen can cause engine damage due to overheating. Keep air intake screen and other external surfaces of the engine, including cooling fins, clean at all times to allow adequate air intake.
Touching hot surfaces can burn skin. The engine, components, and fluids will be hot if the engine has been running. Allow the engine to cool before servicing or working near the engine and components.
Park machine safely. (See Parking Safely in the SAFETY Section.)
Remove hood. (See Removing and Installing Hood in SERVICE MISCELLANEOUS Section.)
Clean air intake screen and external engine surfaces. (See Cleaning Air Intake Screen and Engine Fins in SERVICE ENGINE Section.)
MXAL46387-UN: Air cleaner coverRemove air cleaner cover (A) and air filter. (See Checking and Cleaning Air Cleaner Element in SERVICE ENGINE Section.) Remove three bolts (B) and rotating screen (C).
IMPORTANT:
Be careful to maintain position of fuel pump assembly (D), clips (E) for fuel line, and any other attached components when removing parts from side of engine.
Remove fuel pump screws (F) and fuel line bracket bolts (G).
Remove bolts and engine shroud (H).
MXAL46388-UN: FanClean debris from: Fan areas (I)
Cylinder head cooling fins (J)
Area between engine and frame
IMPORTANT:
Engine shroud must be assembled so that the slots in the shroud align with the ridge in the air intake and mating surfaces along sides of engine. Failure to assemble correctly will prevent the air filter from sealing and may cause engine damage.
Install shroud, fuel pump, fuel line guard, and oil fill tube with hardware.
Install rotating screen with three bolts. Tighten bolts to specification.
Item
Measurement
Specification
Engine Rotating Screen Bolt
Torque
3.0 N·m (27 lb-in.)
Install air filter and air cleaner cover.
Install hood.
Replacing Fuel Filter
Fuel vapors are explosive and flammable:
Do not smoke while handling fuel.
Keep fuel away from flames or sparks.
Shut off engine before servicing.
Cool engine before servicing.
Work in a well-ventilated area.
Clean up spilled fuel immediately.
Change filter when fuel is low.
Park machine safely. (See Parking Safely in the SAFETY section).
Lift hood.
Let engine cool.
Put a drain pan under fuel filter.
MXAL46397-UN: Fuel filterSlide hose clamps (A) away from fuel filter (B) using pliers. Disconnect hoses from filter.
IMPORTANT:
Incorrect installation of fuel filter may cause engine damage. Install the filter with the arrow pointing in the direction of fuel flow (towards the engine) for proper operation.
Connect hoses to new filter making sure the filter arrow is pointing in the direction of the fuel flow.
Install clamps and check for leaks.
Lower hood.
Removing Mower (48 and 54 Mower)
Park machine safely. (See Parking Safely in the SAFETY section.)
Allow engine and muffler to cool completely.
CAUTION: Rotating blades are dangerous. Before adjusting or servicing mower:
Disconnect spark plug wire(s) or battery negative (-) cable to prevent engine from starting accidently.
Always wear gloves when handling mower blades or working near blades.
Adjust mower cutting height to lowest position.
MXAL46026-UN: mower deckRotate all mower anti-scalp wheels to allow mower deck to be rolled outward away from machine: Remove locking pin and pin from anti-scalp wheel shaft.
Rotate mower wheel (A) 90°, as shown. Install locking pin and pin to lock wheel in position.
Repeat for all anti-scalp wheels.
CAUTION: If the lift pedal is spring-assisted it may have unexpected movement.
Lock the lift pedal when installing or removing mower deck.
NOTE:If a lift assist is installed on your machine, lower deck and then pull lift pedal back by hand to lock the mower lift lock lever.
Lower mower deck.
CAUTION: Component is spring-assisted and under tension. Injury can occur if spring-assisted component is released suddenly.
Grasp and hold tension rod (B) securely. Disengage rod from retaining bracket (C) by rotating rod counterclockwise. Move rod as far as possible toward rear wheel to remove all belt tension.
MXAL46415-UN: Drive beltRemove separate drive belt (D) from engine sheave (E), and move tension rod back into retaining bracket.
MXAL46416-UN: J-pinPull and rotate J-pin (F) to release and move rear draft arm (G) away from deck bracket (H). Raise deck slightly with deck handle to remove pressure on pin when pulling out. Repeat on other side.
MXAL46417-UN: Draft rodRemove front draft rod (I) from mower bracket (J). When operating the machine without the mower deck:
Remove locking clip (K) from stud (L) on each side, and remove front draft rod from draft bracket (M). Note orientation of stud offset when removing, correct offset is above rod.
Raise draft arms to transport position.
Slide mower out from under the machine.
Installing Mower (48 and 54 Mower)
Park machine safely. (See Parking Safely in the SAFETY section.)
Allow engine and muffler to cool completely.
CAUTION: Rotating blades are dangerous. Before adjusting or servicing mower:
Disconnect spark plug wire(s) or battery negative (-) cable to prevent engine from starting accidently.
Always wear gloves when handling mower blades or working near blades.
Adjust mower cutting height to lowest position.
MXAL46039-UN: draft armSlide mower deck under tractor and line up deck bracket (A) with draft arm (B). Unlock mower lift lock lever.
CAUTION: If the lift pedal is spring-assisted it may have unexpected movement.
Lock the lift pedal when installing or removing mower deck.
Pull lift pedal by hand to lower draft arms. Hold pedal securely and lock mower lift lock lever.
MXAL46040-UN: draft rodInstall front draft rod (C) into mower bracket (D). If draft rod assembly has been removed from machine:
Install mounting stud (E) into draft bracket (F) at each side. Note orientation of stud offset when installing, correct orientation is for stud to be offset above draft rod.
Secure each side with locking clip (G).
Install draft rod into mower bracket.
MXAL46041-UN: deck bracketPull back J-pin (H) and insert through deck bracket (A) and draft arm (B). Make sure pin installs completely through deck bracket. Repeat for other side.
CAUTION: Component is spring-assisted and under tension. Injury can occur if spring-assisted component is released suddenly.
IMPORTANT:The belt will be damaged if installed wrong. Route the belt properly through belt guides. See belt routing label on mower deck.
MXAL46042-UN: drive belt
MXAL46043-UN: tension rodGrasp and hold tension rod (I) securely. Disengage rod from retaining bracket (J) by rotating rod counterclockwise. Move rod as far as possible toward rear wheel. Install separate drive belt (K) onto mower deck and engine sheave (L), and move tension rod back into retaining bracket. Level mower.
Raise the deck to cutting height and rotate all mower anti-scalp wheels (M) to operation position:
Remove locking clip (N) and pin, and move wheel to proper hole position. Install pin and locking clip to secure wheels in position.
Replacing Mower Drive Belt (48 and 54 Mower)
Replacing Primary Belt
Park machine safely. (See Parking Safely in SAFETY section.)
Allow engine and muffler to cool completely.
Lower mower deck.
CAUTION: Component is spring-assisted and under tension. Injury can occur if spring-assisted component is released suddenly.
Remove drive belt tension:
MXAL46053-UN: 48 mower shown. Lever on left side.Grasp and hold tension rod (A) securely. Disengage rod from retaining bracket (B) by rotating rod counterclockwise.
Move rod as far as possible toward rear wheel to remove all belt tension.
MXAL46054-UN: engine sheaveRemove primary mower drive belt (C) from engine sheave (D), and move tension rod back into retaining bracket. Clean belt with a clean cloth.
Inspect belt for wear or damage; replace as necessary.
Install belt on mower sheave and engine sheave.
Pivot drive belt tension rod toward front of machine to tighten drive belt. Hook tension rod into bracket on mower.
Replacing Secondary Belt
Park machine safely. (See Parking Safely in SAFETY section.)
Allow engine and muffler to cool completely.
Remove mower deck.
Remove drive belt:
MXAL46055-UN: 54 mower shown.Remove one cap screw on each belt shield (A), and slide belt shields outward to remove tabs on belt shields from slotted holes (B) in mower deck. Remove bolt and belt guide (C).
Remove small spring locking pin (D), and remove tension rod (E) from tension handle bracket (F).
CAUTION: Components are installed under spring tension. Wear eye protection and use proper tools when installing and removing components with spring tension.
To remove belt, rotate tension arm (G) slightly counter clockwise, and remove belt from sheaves.
Inspect belt for wear or damage; replace as necessary.
Clean top surface of mower deck and sheaves.
Install belt on mower deck as shown. Make sure belt is under tension rod (E), and in the groove of each sheave. If necessary, rotate tension arm (G) slightly to place belt onto the last sheave.
Install and tighten belt guide (C).
Install tension rod (E) onto tension handle bracket (F), and secure with small spring locking pin (D).
Install belt shields onto slotted holes on mower deck and slide each shield towards center of deck. Secure each shield with one cap screw.
Install mower deck.
Removing and Installing the Battery
Removing
Park machine safely. (See Parking Safely in the SAFETY section.)
Raise the hood.
MXAL46432-UN: Battery cablesDisconnect negative (–) battery cable (A). Push red cover (B) away from positive (+) battery terminal and remove cable from battery.
Unhook rubber strap (C).
Remove battery.
Installing
Follow instructions carefully. Battery and battery cables must be installed correctly.
When installing battery, make sure battery terminals are facing toward front of machine.
Place battery on battery tray so battery terminals are facing toward front of machine.
Secure black rubber strap (C).
Connect positive (+) battery cable to ( + ) battery terminal first.
Connect negative (–) battery cable to ( - ) battery terminal.
Apply spray lubricant to terminals to help prevent corrosion.
Slide red cover over positive battery terminal.
Replacing Headlight Bulb
Raise hood.
Locate the headlight bulb.
Turn bulb socket counterclockwise to remove.
Replace defective bulb with new bulb.
Insert bulb socket into housing, push in and turn clockwise to install.
Lower hood.
Replacing Fuse
Park machine safely. (See Parking Safely in the SAFETY section.)
Lift hood.
MXAL46434-UN: Fuse blockPull blown 15 amp fuse (A), 10 amp fuse (B), 20 amp fuse (C), or 7.5 amp fuse (D), out of socket. Fuse identification:
-: Fuse Indentification
Position
Circuit
Fuse Size
A
Main Circuit
15 amp
B
12 Volt Power Port (Optional)
10 amp
C
Starter Circuit
20 amp
D
PTO Circuit
7.5 amp
Check metal strip in fuse window and discard fuse(s) if strip is broken.
Push new 15, 20, 10, or 7.5 amp fuse into correct socket.
Lower hood.
Removing and Installing Wheel Assembly (Models with E-Clip)
Removing
Park machine safely. (See Parking Safely in the Safety section.)
CAUTION: The machine can fall or slip from an unsafe lifting device or supports.
Use a safe lifting device rated for the load to be lifted.
Lower machine onto jack stands or other stable supports and block wheels before servicing.
IMPORTANT:Place jack stands under frame, not under transmission or engine, when raising or supporting machine.
Raise machine with a safe lifting device and lower machine onto jack stands or other stable supports. Block wheels remaining on the ground to prevent machine movement.
MXAL46438-UN: Axle hubRemove the cap (A) from the end of the axle hub.
CAUTION: Components are installed under spring tension. Wear eye protection and use proper tools when installing and removing components with spring tension.
Remove the E-clip (B) and washer (C).
NOTE:
When removing rear wheel assembly, a shaft key may fall out of the axle shaft. If so, be sure to retain for installation.
Remove the wheel assembly.
CAUTION: Explosive separation of tire and rim parts is possible when they are serviced incorrectly:
Do not attempt to mount a tire without the proper equipment and experience to perform the job.
Take wheel assembly to an authorized service dealer for repairs.
Installing
Apply multipurpose grease to spindle shaft before installing wheel assembly.
NOTE:
On rear wheel, be sure shaft key is in place on axle shaft before installing wheel assembly.
Install wheel assembly with valve stem to the outside and align slot in wheel assembly with key in axle shaft.
Install washer and E-clip.
Install cap.
Removing and Installing Wheel Assembly (Models with Wheel Bolt)
Removing
Park machine safely. (See Parking Safely in the Safety section.)
CAUTION: The machine can fall or slip from an unsafe lifting device or supports.
Use a safe lifting device rated for the load to be lifted.
Lower machine onto jack stands or other stable supports and block wheels before servicing.
IMPORTANT:Place jack stands under frame, not under transmission or engine, when raising or supporting machine.
Raise machine with a safe lifting device and lower machine onto jack stands or other stable supports. Block wheels remaining on the ground to prevent machine movement.
MXAL46439-UN: Wheel may or may not have a cap (A) to remove when removing the wheel.Remove the wheel bolts (B). Remove the wheel assembly.
CAUTION: Explosive separation of tire and rim parts is possible when they are serviced incorrectly:
Do not attempt to mount a tire without the proper equipment and experience to perform the job.
Take wheel assembly to an authorized service dealer for repairs.
Installing
Apply multipurpose grease to spindle shaft before installing wheel assembly.
Install wheel assembly with valve stem to the outside.
Tighten wheel bolts evenly in alternating sequence until snug.
Lower machine completely to the ground.
Tighten wheel bolts to specification.
Item
Measurement
Specification
Wheel Bolts
Torque
88 N·m (65 lb-ft)
Electrical
-: Electrical
If | Check |
Starter Does Not Work Or Will Not Turn Engine |
|
Battery Will Not Charge |
|
Lights Do Not Work |
|
Machine
-: Machine
If | Check |
Machine Vibrates Too Much or Rattles Excessively |
|
Machine Will Not Move With Engine Running |
|
Machine Moves With Engine Running and Hydrostatic Control in Neutral |
|
Mower Lift Will Not Latch in Transport |
|
Identify Parts
Operator’s Manual
Safety DVD
Warranty Cards and Warranty Statement
Hardware for Steering Wheel
Seat Springs
Hardware for Battery Cables
Stamped and Padded Key
POP Card and POP Display
Install Steering Wheel
Install steering wheel onto steering shaft. Turn steering wheel to position front wheels straight and facing forward.
Remove steering wheel.
Put John Deere Multi-Purpose lubricant or an equivalent on the steering shaft.
MXAL46441-UN: Steering wheelInstall steering wheel onto steering shaft with one spindle (A) positioned at 180° at bottom of wheel and spindles (B) at approximately 45° at top of wheel. Install nut (C) and tighten to specification.
Item
Measurement
Specification
Steering Wheel Nut
Torque
38 N·m (28 lb-ft)
MXAL46442-UN: CoverInstall cover (D) so that the logo is on the right side facing up.
Remove Shipping Support Rod (54 Mower)
Remove support rod (A) from left side of deck.
Discard rod.
Fuel System
-: Fuel System
Fuel Types (Recommended): | |
..............Regular Grade 87 Octane Unleaded Fuel | |
..............Ethanol Blended Fuel (Up to 10%) | |
..............MTBE Reformulated Fuel (Up to 15%) | |
Fuel Filter ..............Replaceable - paper element | |
Fuel Pump ..............Pulse | |
Fuel Delivery ..............Carburetor |
Engine Warranty Maintenance Statement
Maintenance, repair, or replacement of the emission control devices and systems on this engine, which are being done at the customer’s expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized John Deere dealer.
Emission Control System Certification Label
Tampering with emission controls and components by unauthorized personnel may result in severe fines or penalties. Emission controls and components can only be adjusted by EPA and/or CARB authorized service centers. Contact your John Deere Retailer concerning emission controls and component questions.
The presence of an emissions label signifies that the engine has been certified with the United States Environmental Protection Agency (EPA) and/or California Air Resources Board (CARB).
The emissions warranty applies only to those engines marketed by John Deere that have been certified by the EPA and/or CARB; and used in the United States and Canada in off-road mobile equipment.
Limited Battery Warranty For Factory Installed Batteries
Applicable in North America only. For complete machine warranty, reference a copy of the John Deere warranty statement. Contact your John Deere dealer to obtain a copy.
TO SECURE WARRANTY SERVICE
The purchaser must request warranty service from a John Deere dealer authorized to sell John Deere batteries, and present the battery to the dealer with the top cover plate codes intact.
FREE REPLACEMENT PERIOD
Any new battery which becomes unserviceable (not merely discharged) due to defects in material or workmanship within the FREE REPLACEMENT PERIOD will be replaced free of charge. Installation costs will be covered by warranty if the unserviceable battery was installed by a John Deere factory or dealer and the replacement battery is installed by a John Deere dealer.
PRO RATA ADJUSTMENT (batteries with letter code identification only)
Any new battery which becomes unserviceable (not merely discharged) due to defects in material or workmanship within the Pro Rata Warranty Period will be replaced upon payment of the battery’s current list price less a pro rata credit for unused months of service. The applicable adjustment period is determined from the Warranty Code printed at the top of the battery and table below. Installation costs are not covered after the battery warranty period has ended.
THIS WARRANTY DOES NOT COVER
A. Breakage of the container, cover, or terminals.
B. Depreciation or damage caused by lack of reasonable and necessary maintenance or by improper maintenance.
C. Transportation, mailing, or service call charges for warranty service.
D. Batteries that are merely discharged.
LIMITATION OF IMPLIED WARRANTIES AND PURCHASER’S REMEDIES
To the extent permitted by law, neither John Deere nor any company affiliated with it makes any warranties, representations, or promises as to the quality, performance or freedom from defect of the products covered by this warranty. IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT APPLICABLE, SHALL BE LIMITED IN DURATION TO THE APPLICABLE ADJUSTMENT PERIOD SET FORTH HERE. THE PURCHASER’S ONLY REMEDIES IN CONNECTION WITH THE BREACH OR PERFORMANCE OF ANY WARRANTY ON JOHN DEERE BATTERIES ARE THOSE SET FORTH HERE. IN NO EVENT WILL THE DEALER, JOHN DEERE OR ANY COMPANY AFFILIATED WITH JOHN DEERE BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. (Note: Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages. So these limitations and exclusions may not apply to you.) This warranty gives you specific legal rights, and you may also have some rights which vary from state to state.
NO DEALER WARRANTY
The selling dealer makes no warranty of its own and the dealer has no authority to make any representation or promise on behalf of John Deere, or to modify the terms or limitations of this warranty in any way.
WARRANTY TERMS TABLE
If your battery is not labeled with a warranty code, it is a warranty code 6.
-: PRO RATA MONTHS OF ADJUSTMENT
Warranty Code | Free Replacement Period | Pro Rata Warranty Period |
A | 90 Days | 40 Months |
B | 90 Days | 36 Months |
C | 90 Days | 24 Months |
D | 12 Months | 48 Months |
E | 90 Days | 12 Months |
F | 90 Days | 60 Months |
G | 12 Months | 60 Months |
H | 12 Months | 60 Months |
6 | 6 Months | 0 Months |
12 | 12 Months | 0 Months |
18 | 18 Months | 0 Months |
The RSX850i original equipment battery will carry a 100% Full Replacement for the duration of the complete machine warranty.
Tire Warranty
John Deere warranty applies for tires available through the John Deere parts system. For tires not available through the John Deere parts system, the tire manufacturer’s warranty applicable to your machine may not apply outside the U.S. (See your John Deere dealer for specific information.)
Slope Gauge Template
Cut along left boundary line of graphic as a guide to remove template.
-: Slope Gauge
Use this slope gauge to determine if a slope is too steep for safe operation. Do not operate your machine on a slope greater than what is recommended in your Operator’s Manual. See Operating on Slopes in the Safety Section. |
• Fold along the appropriate line (A) to match the recommended slope. |
• Align this edge (B) with a vertical surface, a tree, building, fence pole, etc. |
• Compare slope (C) with folded edge. |
-: Blank Page
Attachments for Your Machine
There’s a John Deere attachment or kit to make your new machine perform more tasks or be more versatile, whether your machine is a lawn tractor or compact utility tractor or a utility vehicle.
You can check out the entire line of attachments for your machine at JohnDeere.com or ask your John Deere dealer. From aerators to electric lift kits to tillers, there’s a John Deere attachment or kit to fill every need.
California and U.S. EPA Emissions Control System Warranty Statement (Off-Road Gas Engines)
Your Warranty Rights and Obligations
The California Air Resources Board, John Deere, and the United States Environmental Protection Agency are pleased to explain the emissions control system’s warranty on your model year 2015 or 2016 spark ignited off-road engine equipment. In California, new equipment that uses small or large (less than 1 liter) spark ignited off-road engines must be designed, built and equipped to meet the State’s stringent anti-smog standards. John Deere must warrant the emissions control system on your spark ignited off-road engine equipment for the period listed below provided there has been no abuse, neglect or improper maintenance of your equipment.
Your emissions control system may include parts such as: carburetors or fuel-injection system, ignition system, catalytic converters, fuel tanks, valves, filters, clamps, connectors, and other associated components. Also included may be hoses, belts, sensors and other emission-related assemblies.
Where a warrantable condition exists, John Deere will repair your spark ignited off-road engine equipment at no cost to you including diagnosis, parts and labor.
Manufacturer’s Warranty Coverage
This emissions control system is warranted for two years. If any emissions related part on your equipment is defective, the part will be repaired or replaced by John Deere.
Owner’s Warranty Responsibilities
As the spark ignited off-road engine equipment owner, you are responsible for the performance of the required maintenance listed in your Operator’s Manual. John Deere recommends that you retain all receipts covering maintenance on your spark ignited off-road engine equipment, but John Deere cannot deny warranty solely for lack of receipts or for your failure to ensure the performance of all scheduled maintenance.
As the spark ignited off-road engine equipment owner, you should however be aware that John Deere may deny you warranty coverage if your spark ignited off-road engine equipment or a part has failed due to abuse, neglect, or improper maintenance or unapproved modifications.
You are responsible for presenting your spark ignited off-road engine equipment to a John Deere Turf and Utility distribution center or service center as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question regarding your warranty coverage, you should contact your John Deere Turf and Utility retailer, or the John Deere Customer Contact Center at 1- 800-537-8233, or e-mail John Deere from www.Deere.com.
General Emissions Warranty Coverage
The warranty period begins on the date the equipment is delivered to an ultimate purchaser. John Deere warrants to the ultimate purchaser and each subsequent purchaser that the spark ignited off-road engine equipment is:
Designed, built and equipped so as to conform to all applicable regulations adopted by the California Air Resources Board;
Designed, built and equipped so as to conform at the time of sale with applicable U.S. Environmental Protection Agency regulations under 40 CFR Parts 1054 and 1060: and,
Free from defects in materials and workmanship which cause such engine to fail to conform with applicable regulations for a period of two years of engine use from the date of sale to the ultimate purchaser.
Emissions Warranty Interpretation
Any warranted part that is not scheduled for replacement as required by the maintenance instructions in the Operator’s Manual is warranted for two years. If any such part fails during the period of warranty coverage it will be repaired or replaced by John Deere. Any such part repaired or replaced under warranty is warranted for the remaining warranty period.
Any warranted part that is scheduled only for regular inspection in the maintenance instructions in the Operator’s Manual is warranted for two years. A statement in the Operator’s Manual to the effect of “repair or replace as necessary” does not reduce the period of warranty coverage. Any such part repaired or replaced under warranty is warranted for the remaining warranty period.
Any warranted part that is scheduled for replacement as required maintenance in the Operator’s Manual is warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part will be repaired or replaced by John Deere. Any such part repaired or replaced under warranty is warranted for the remainder of the period prior to the first scheduled replacement point for the part.
Repair or replacement of any warranted part under the warranty will be performed at no charge to the owner at any authorized John Deere Turf and Utility retailer.
The owner will not be charged for diagnostic labor which leads to the determination that a warranted part is defective, provided such work is performed by John Deere.
John Deere will repair damages to other engine components proximately caused by a failure under warranty of any emissions-related warranted part.
Add-on or modified parts that are not exempted by the California Air Resources Board may not be used. The use of any non-exempted add-on or modified parts will be grounds for disallowing a warranty claim. John Deere will not be liable to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.
Emission Warranty Parts List
Coverage under this warranty extends only to the parts listed below (the emissions control system parts) to the extent these parts were on the engine and equipment purchased.
Fuel Metering System:
Carburetor and internal parts (or fuel injection system)
Air/fuel ratio feedback and control system
Cold start enrichment system
Evaporative System:
Fuel tank, fuel cap and tether
Fuel hose, line, fittings, clamps
Fuel pump, fuel shut-off valve
Fuel vapor hoses, fittings
Carbon canister
Rollover/slant valve for fuel vapor control
Purge and vent line
Air Induction System:
Air cleaner
Intake manifold
Ignition System:
Spark plugs
Magneto or electronic ignition system
Spark advance/retard system
Exhaust System:
Exhaust manifold
Catalyst muffler
Miscellaneous Items Used in Above Systems
Valves and Switches: vacuum, temperature, position, check, time-sensitive
Electronic controls
Hoses, belts, connectors and assemblies
Limited Liability
a) The liability of John Deere under this Emissions Control System Warranty is limited solely to the remedying of defects in materials or workmanship. This warranty does not cover inconvenience or loss of use of the non-road equipment or engine or transportation of the equipment or engine to or from the John Deere Turf and Utility retailer. John Deere shall not be liable for any other expense, loss, or damage, whether direct, incidental, consequential (except as listed above under “coverage”) or exemplary arising in connection with the sale or use of or inability to use the non-road equipment or engine for any other purpose.
b) No express emissions control system warranty is given by John Deere with respect to the equipment or engine except as specifically set forth in this document. Any emissions control system warranty implied by law, including any warranty of merchantability or fitness for a particular purpose, is expressly limited to the emissions control system warranty terms set forth in this document.
c) No dealer is authorized to modify this Federal, California and John Deere Emissions Control System Warranty.
Understanding The No-Text Machine Safety Labels
At several important places on this machine safety signs are affixed intended to signify potential danger. The hazard is identified by a pictorial in a warning triangle. An adjacent pictorial provides information how to avoid personal injury. These safety signs, their placement on the machine and a brief explanatory text are shown in this Safety section.
There can be additional safety information contained on parts and components sourced from suppliers that is not reproduced in this operator’s manual.
Read Operator’s Manual
This operator’s manual contains important information necessary for safe machine operation.
Carefully read operator’s manual before operating machine. Observe all safety rules to avoid accidents.
Avoid Injury From Loaded Spring
Keep fingers and hands away from pinch point.
Read operator’s manual.
Keep Children Away from Mower
Mower can cause dismemberment or death.
Stay a safe distance from the machine.
Make sure that children stay clear of mower at all times when the engine is running.
Avoid Injury From Tipping
Do not drive where machine could slip, tip, or rollover.
In some configurations, do not drive or operate on a slope of more than 10 degrees.
Refer to the Operating on Slopes section for more information.
Avoid Injury From Thrown Objects
Keep a safe distance from the machine as long as the engine is running.
Prevent Equipment Fires
Clean and inspect the entire machine.
Carefully read Operator’s Manual Machine Cleanout section for details.
Avoid Injury From Rotating Blades
Do not put hands or feet under or into mower when engine is running.
Do not operate mower without discharge chute or entire grass catcher in place.
TH84124,0000199-19-20120912TH84124,000019A-19-20121119MX00654,000020B-19-20140821MX00654,000020C-19-20140821CAUTION: IMPORTANT:NOTE:MX00654,000020D-19-20140821OUO1023,0000035-19-20130221MXAL41929-UN: Protect children warning symbolOUO1023,0000037-19-20130221MXAL41930-UN: Keep riders off symbolOUO1023,0000039-19-20130221GXAL42347-UN: Read operator's manual symbolOUO1023,000017D-19-20130301MXAL42363-UN: WarningNOTE:MP47322,00F4601-19-20140821MP47322,00F4616-19-20130708MXAL41932-UN: WARNINGMP47322,00F4617-19-20140314MXAL41928-UN: WARNINGMP47322,00F4619-19-20130315MP47322,00F461D-19-20130315MXAL41935-UN: Wear Appropriate ClothingMP47322,00F461E-19-20130315MXAL42880-UN: Driving SafelyMP47322,00F461F-19-20130315MXAL41933-UN: Safe MaintenanceMP47322,00F4620-19-20130315MXAL41927-UN: Avoid High Pressure FluidsMP47322,00F4621-19-20130315MXAL41938-UN: Handling Fuel SafelyMP47322,00F4623-19-20130315MXAL41937-UN: Tire SafetyMP47322,00F4624-19-20130315MP47322,00F4625-19-20130315MP47322,00F4626-19-20130315MP47322,00F4627-19-20130528CAUTION: MP47322,00F4628-19-20130325MP47322,00F4629-19-20130315MP47322,00F462A-19-20130531MP47322,00F462B-19-20130315MP47322,00F462C-19-20130315MP47322,00F4630-19-20130613MXAL42804-UN: WarningCAUTION: MP47322,00F4637-19-20130315MP47322,00F4638-19-20130319MP47322,00F4639-19-20130620MP47322,00F463A-19-20130327CAUTION: CAUTION: MP47322,00F4646-19-20130315IMPORTANT:MP47322,00F464B-19-20130315IMPORTANT:MP47322,00F464D-19-20130315CAUTION: MP47322,00F4652-19-20130315MXAL42826-UN: Oil ChartMP47322,00F4653-19-20130315NOTE:MP47322,00F465A-19-20130315MP47322,00F466C-19-20130315MP47322,00F466E-19-20130315MXAL42869-UN: WarningCAUTION: MP47322,00F466F-19-20130315MP47322,00F4671-19-20130315CAUTION: MXAL42872-UN: Battery Booster ConnectionLEGEND: A - Booster BatteryB - Disabled Vehicle BatteryMP47322,00F4672-19-20130315IMPORTANT:MP47322,00F4674-19-20130315CAUTION: IMPORTANT:MP47322,00F4675-19-20130315CAUTION: MP47322,00F4677-19-20130620MP47322,00F467A-19-20130315MP47322,00F467B-19-20130315CAUTION: MP47322,00F4680-19-20130315MP47322,00F4681-19-20130315NOTE:MP47322,00F4682-19-20130528MP47322,00F4683-19-20130315MP47322,00F4690-19-20140821TCAL41258-UN: John Deere LogoSP66632,00043A7-19-20130404MXAL45931-UN: Danger Rotating BladesSP66632,0004451-19-20130415MXAL45934-UN: Rotating BladeSP66632,0004454-19-20130415MXAL45936-UN: Located on batterySP66632,0004456-19-20130817MXAL45937-UN: WarningSP66632,0004457-19-20130415MXAL45938-UN: WarningSP66632,0004458-19-20130415MXAL45945-UN: Prevent firesSP66632,000445F-19-20130817SP66632,0004486-19-20130817CAUTION: SP66632,0004488-19-20130409SP66632,000448D-19-20130409CAUTION: NOTE:SP66632,000448E-19-20130409CAUTION: NOTE:SP66632,000448F-19-20130409CAUTION: MXAL45983-UN: Steering WheelSP66632,0004490-19-20130802CAUTION: NOTE:SP66632,0004491-19-20130415NOTE:SP66632,0004492-19-20130409NOTE:SP66632,0004493-19-20130409NOTE:SP66632,0004494-19-20130415MXAL46374-UN: Cargo mountSP66632,000449B-19-20130409SP66632,000449E-19-20130409SP66632,00044A6-19-20130409MXAL46378-UN: Rear U-JointsSP66632,00044A7-19-20130416MXAL45999-UN: Location of grease fitting under left side of deck.SP66632,00044A8-19-20130409IMPORTANT:NOTE:SP66632,00044AD-19-20130415CAUTION: IMPORTANT:CAUTION: SP66632,00044B0-19-20130415CAUTION: NOTE:SP66632,00044B4-19-20130415SP66632,00044BB-19-20130416SP66632,00044BE-19-20130416SP66632,00044C3-19-20130416IMPORTANT:SP66632,00044CA-19-20130415SP66632,00044CD-19-20130409SP66632,00044CE-19-20130823SP66632,00044D4-19-20130409SP66632,00044D5-19-20130409SP66632,00044DA-19-20130409SP66632,00044DB-19-20130411SP66632,00044E1-19-20130409SP66632,00044E3-19-20130415MXAL46444-UN: Support rodSP66632,00044E5-19-20130409SP66632,000459B-19-20130410NOTE:OUMX068,00004FE-19-20130715NOTE:NOTE:OUMX068,0000504-19-20140821MX00654,0000314-19-20140821NOTE:MXT007077-UN: Slope Gauge TemplateOUMX068,0000513-19-20130625OUMX068,000051C-19-20140821MX00654,0000362-19-20140821TCT005498-UN: Safety alert symbolMX00654,0000389-19-20140821MXAL42776-UN: Read Operator’s ManualMX00654,000038B-19-20140821MXAL42777-UN: Pinch PointMX00654,000038C-19-20130616MXAL42778-UN: Keep Children Away from MowerMX00654,000038D-19-20130722MXAL42779-UN: Avoid Injury from TippingMX00654,000038E-19-20130724MXAL42780-UN: Avoid Injury From Thrown ObjectsMX00654,000038F-19-20130724MXAL42781-UN: Prevent Equipment FiresMX00654,0000390-19-20140821MXAL42784-UN: Avoid Injury From Rotating BladesMX00654,0000392-19-20130724
![[DA] ACME CPG](https://sprcdn-assets.sprinklr.com/1436/a7d6e3dd-fbc7-4292-a20c-e8f9964348e5-1036124649.png)
